![]() ![]() Stay on curb lines, centerlines, bottom of slope, etc., without operator effort. Automatically follow guidance lines from design plans with Steer Assist 3D.Cat Grade with 3D has no masts – low profile antennas are integrated into the cab roof and GNSS/GPS receivers are mounted inside the cab for better protection.Factory integrated Cat Grade with 3D uses GNSS/GPS to control the blade so you can get to design plan faster.*Feature not operational indoors or in areas where a GNSS/GPS signal is not available. Attachment Ready Option (ARO) provides wiring and mounting provisions for dealer installation of Grade with 3D, Accugrade, UTS, or other grade control systems.Slope Indicate is included in the main machine display and shows side slope and uphill/downhill grades to help operators with slope work.AutoCarry automates blade lift to help you maintain consistent blade load and reduce track slip.*.Traction Control automatically reduces track slip to save you time, fuel and track wear.*.Actively monitors machine load and track slip to help you reach optimal pushing capacity.* Blade Load Monitor gives you real-time feedback on current load versus the optimal blade load based on your ground conditions.Stable Blade works seamlessly with operator inputs to help produce a smoother surface when operating manually.Helps reduce operator fatigue by automatically maintaining straight travel with light loads or heavy loads on flat ground and side slopes. Steer Assist automates track and blade tilt steering.For machines with 3D, operators can easily switch back and forth from full 3D automatics to Slope Assist. Cat Grade with Slope Assist™ automatically maintains pre-established blade position without a GNSS/GPS signal – no additional hardware or software needed.Seasoned operators can enjoy reduced effort and fatigue, along with faster, more accurate results. Some blade and steering functions are automated so newer operators can work at productivity levels closer to their veteran counterparts. Individual results may vary based on application, hour utilization, operator and other factors.Assist features help make work easier, especially for less experienced operators. Estimates based on average cost per bank cubic meters (cubic yards) of material moved in typical construction applications with 1,500 hours/year. Note: All comparisons to 2014-2016 3-speed D6T dozerġ Productivity = BCM (BCY)/hour, fuel consumption = L (gal)/hour. Available in VPAT or push arm configurations with standard or two widths of Low Ground Pressure (LGP) undercarriage.Distributed cab heating/cooling with automatic temperature and blower control circulates air more effectively.touchscreen display and standard wider air suspension seat or heated/cooled leather seat options Cat C9.3B diesel engine features a redesigned fuel system, elimination of the NOx Reduction System and a simplified single engine Electronic Control Module (ECM).Optional Heavy Duty Extended Life undercarriage with Positive Pin Retention pins and link improvements for up to 20% more seal life in high impact conditions.Up to 12% reduction in service and maintenance costs via updated components, longer service intervals and fewer scheduled maintenance tasks.Intuitive Technologies on Cat D6 Dozers Enhance Operator Performance ![]() Cat GRADE with Slope Assist provides basic blade positioning assistance without the need for added hardware or a GPS signal.įactory Attachment Ready Option (ARO) provides optimal mounting locations, brackets, and hardware and simplifies installation of an aftermarket grade control system. Smaller antennas are integrated into the cab roof for even better protection. AutoCarry is included to automate blade lift to maintain desired blade load, improving load consistency and reducing track slip.Ĭat Slope Indicate is standard, showing the machine cross-slope and fore/aft orientation on the primary monitor for quick and easy reference. The system uses advanced Inertial Measuring Units (IMU), which provide greater speed and accuracy without position sensing cylinders. touch screen and more intuitive operator interface. The dozers are available with an updated, factory integrated Cat GRADE with 3D system with a 10-in. New Caterpillar D6 Models Offer a Beefier Yet Lighter Weight Structure A new optional finish grading undercarriage has ten bottom rollers for smoother grades at higher speeds, even in difficult surfaces like sand and gravel. centered shoes, puts more track on the ground to reduce ground pressure to 5 psi. A wide gauge LGP VPAT design, with 36-in. The Variable Power Angle Tilt (VPAT) dozer has a redesigned structure that is stronger, yet lighter, so machine balance is optimized for grading without the need for a rear implement or counterweight. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |